Which primer for which surface?
How to find the right primer for plaster, plasterboard, wood, metal and facades.
A primer makes sure the new coat looks even and lasts. It evens out surfaces that absorb differently, consolidates slightly sandy substrates or improves adhesion on smooth surfaces. Which primer you need depends on the surface. You will find all the products mentioned under Primers.
Four steps to the right primer
- Check the surface: It must be firm, dry, clean and sound. The article General information on the substrate explains what this means in detail.
- Do a wipe test: Wipe the surface with the flat of your hand. If paint or sand sticks to your hand, the surface needs to be consolidated.
- Test the absorbency: Spray or brush a little water onto the surface. If it soaks in immediately, the surface is highly absorbent. If it beads off, it is weakly absorbent or smooth.
- Choose the primer: Use the table below. Let the primer dry completely before the next coat; the drying time is on the container and in the technical data sheet.
Interior walls and ceilings
| Surface / problem | Suitable primer |
|---|---|
| Absorbent or slightly sandy plaster, gypsum plaster, gypsum filler, concrete | Lacryl Tiefgrund ELF 595 (transparent, consolidating) or Lacryl Hydro-Gel ELF 695 (easy to roll) |
| Highly or unevenly absorbent mineral surfaces, e.g. plaster, aerated concrete | Grundierkonzentrat ELF 938, diluted with water |
| Plasterboard, gypsum plaster, concrete, matt old paint; also as a white wallpaper base | Wand-Primer ELF 3729 or Wand-Primer grob ELF 3728 (pigmented, opaque) |
| Smooth or weakly absorbent surfaces, surfaces with grazing light | Haftgrund ELF 3720 |
| Water, nicotine, soot or oil stains | Isogrund 924 (water-based), Isoliergrund 115 (synthetic resin) or the stain-blocking paint Aqualoma ELF 202 |
| Mineral surfaces before a silicate paint | Fondosil 1903 |
| Before wallpapering, especially with light or translucent wallpapers | Pufas Tapetengrund weiß |
Wood and metal
| Surface | Suitable primer |
|---|---|
| Wood inside and outside, especially light paints on wood with staining extractives | Isoprimer 243 (water-based) or Impredur Grund 835 (alkyd resin) |
| Iron and steel, including radiators | Haftgrund 850 (rust-passivating, heat-resistant up to +180 °C) |
| Zinc, galvanised steel, aluminium, paintable plastics, sound old paint | Lacryl Allgrund 246 |
| Difficult, very smooth surfaces such as powder coating or coil coating | 2K-Epoxi Varioprimer 865 |
Facade
| Surface | Suitable primer |
|---|---|
| Absorbent mineral surfaces, e.g. exterior render | Secobase 916 (transparent, silicone system) |
| Weakly absorbent, sound matt emulsion paint | Secoprime 917 (pigmented) |
| Before a render or mineral lightweight render | Putzgrundierung 3710 (contains quartz) |
| Before a silicate paint | Fondosil 1903 |
Frequently asked questions
Do I need to prime a wall that has already been painted? Usually not, if the old paint is firm and the new colour is similar. You will find details in the article Do painted wall surfaces need to be primed again?
Which primer do I need for Terrastone or clay plaster? Here we recommend the quartz-containing Pufas Putzgrund weiß P32.
Can the primer be tinted? Yes. Our Brillux products are listed in white in the shop; we mix your chosen colour on request. More on this under Brillux paints in the colour of your choice.